View The Full Version : DPF removal EGR on the Alfa 159 2.4 JTDM
Nightwing
04-12-2012, 22:14
Hello guys, I was able to find the Time to remove the DPF and EGR on my 159, for curiosity? and for trying to understand what they were going to change the program, I've made 3 Mod file, one with eslusione DPF, one to the exclusion EGR and one to the exclusion of both, by analyzing the file with Ecm Titanium 1.61 mode? 2D I have seen some of the parameters changed, but I don't know if they were made in the correct way.
Can you give me more? lumens about it?
Thanks
I'm attaching the 3 Mod file + file Ori.
magi1984
04-12-2012, 23:12
the time on these ecu works without problems
msport (exil77grande)
05-12-2012, 09:46
I confirm that I sure it was done correctly.
Nightwing
05-12-2012, 10:09
Gianpy80
05-12-2012, 10:27
Nightwing
05-12-2012, 10:56
no light on?
The same ebayer sells anke Downpipe, for if you have installed anke what?
msport (exil77grande)
05-12-2012, 11:14
no light on?
The same ebayer sells anke Downpipe, for if you have installed anke what?
you're going off-topic.
Nightwing
05-12-2012, 11:33
ops, sorry:(
Nightwing
06-12-2012, 20:31
:confused::confused::confused: I doubt there is a......once remapped the ecu with the changes made since the time for the DPF I put the tube straight and sn in place, but for the EGR I have to make no other changes or just the electronic lock on the main map?
msport (exil77grande)
06-12-2012, 20:40
:confused::confused::confused: I doubt there is a......once remapped the ecu with the changes made since the time for the DPF I put the tube straight and sn in place, but for the EGR I have to make no other changes or just the electronic lock on the main map?
then the electronic lock enough but if you want to be picky, I would do:
cleaning the egr-valve
closing the physics of egr-valve
electronic closure of the egr valve.
Nightwing
06-12-2012, 20:49
Thanks a lot msport :cool:
magi1984
06-12-2012, 21:09
Nightwing
06-12-2012, 21:29
I was willing/forced to do it all together, thanks to some friends that I lend the bridge and the workshop, disassemble, clean, rimappo and then off to the test bench:cool:
Hello guys, thanks to this forum I tried to defappare my 159 2.4
I did the following steps
-) reading the file from the ecu with mpps
-) luca stanca with ecusafe
-) correction-bit jamming with ecm titanium from -6 to 400
I enclose the map, you can give him an eye.
thanks in advance
With the 159 2.4 game in the house.....but I have not seen your presentation as you should do for the regulation. Hello
I was willing/forced to do it all together, thanks to some friends that I lend the bridge and the workshop, disassemble, clean, rimappo and then off to the test bench:cool:
if I were you, I'd eliminate the swirl...both electronically and physically...
those car are suffering already from the gold of rupture of those components...with a remap, where you surely will go to increase the press the turbo and the swirl are really at risk of breakage....only that electronically gets it soon...
and for the physical elimination of the swirl that created the problems..
I have made a little time ago and to delete all saw that the swirl was broken I had to come down the inlet manifold(before you removed timing belt and pump common rail) then I threaded the holes on the manifold with a male 18x1,5, and I capped with appropriate caps to measure....
a lot of work, but it is false worth...
the car with automatic transmission flap in the first three gears acceleration, and squirts away to the slightest pressure of the pedal despite the weight...
just to chirezza is not that togliendpo the swirl increases something in the power...
only that when the car in question she came to me in the workshop had the dpf clogged,the egr blocked and the swirl routes..
in addition to having the inlet manifold full of crap the black is oily... so is not walking for nothing era in recovery mode and it only did 120 km/h...after the treatment munro has been reborn....255 km/h gps...
Hello guys, thanks to this forum I tried to defappare my 159 2.4
I did the following steps
-) reading the file from the ecu with mpps
-) luca stanca with ecusafe
-) correction-bit jamming with ecm titanium from -6 to 400
I enclose the map, you can give him an eye.
thanks in advance
Ok....in view of the presentation.I advise you not to use sw luca stanca on this car that has the ability to change layout without the dpf through a single switch off so you can remain active all the dtc's that the sw is smooth.
It would be nice to be able to do it.....but I don't know where to start....can you help me?
I learned thanks to the forum then it is fair to share to those who do not know. 1DE432 display 8-bit take it from 1 to 2 . 1e46ee in 16-bit carry from 400 to val max 65535. And the dpf is as if there were
Many thanks.I feel at the end of the week.I must do the csf with ecuscan?before writing the file in the ecu with mpps,I have to give the checksum of the modified file in the ecm?
both ecm mpps correct automatically the checksum...
Tube fap finally arrived. Is it okay if I proceed as follows:
1) load the file with the switch-ff as recommended from a friend errrcinque
2) can I change the mechanical part
3) changing the oil and resetto errors of waste oil with ecuscan
Should I do another?
Thanks
Errecinque
13-11-2015, 09:37
Tube fap finally arrived. Is it okay if I proceed as follows:
1) load the file with the switch-ff as recommended from a friend errrcinque
2) can I change the mechanical part
3) changing the oil and resetto errors of waste oil with ecuscan
Should I do another?
Thanks
I would say that it is all correct. When you enter the diagnosis after you have loaded the map controls the setting that is without dpf and clogging up to 1000%
Remap done.
Ecuscan tells me the filter is not clogged, and clogging up to 1000.
Everything should be ok.
Tomorrow I put the tube....will update on how it goes
Thanks
I learned thanks to the forum then it is fair to share to those who do not know. 1DE432 display 8-bit take it from 1 to 2 . 1e46ee in 16-bit carry from 400 to val max 65535. And the dpf is as if there were
Hello Errecinque, this speech is also good for the 159 1.9 jtdm 150 hp?
If euro 4 yes, the same discourse. The addresses may be different, but just comparing the areas in 2d the individuals easily
Thanks Errecinque! My first step will be to power off the electronic EGR since it is already broken, locked in closing, I cleaned but nothing has changed....then I will make the DPF
I think that if it has failed electrically you must also delete the dtc that you leave in a diagnosis after having disabled the usual procedure of panettone
ok thanks for the tips....I...the operation I'm going to do with galletto1260 as an interface and a time ( my friend's) to process the file ori, I have read in the forum to work quietly on my ecu. As you may have understood, I am very beginner.
I have personally used the Time on an Alfa 159 1.9 16v jtdm with dpf and I have deleted the egr and fap. The result is ok but I recommend you should always, before writing the file, open the map ori and mod it with software (ECM for example) and re-save the map mod to have a checksum is already correct!
ok thanks for the tips....I...the operation I'm going to do with galletto1260 as an interface and a time ( my friend's) to process the file ori, I have read in the forum to work quietly on my ecu. As you may have understood, I am very beginner.
Let it be a time...get the map above to whom I have given the addresses over bit for the switch and look for them on your map. Put them in the values and the time is not needed
I have personally used the Time on an Alfa 159 1.9 16v jtdm with dpf and I have deleted the egr and fap. The result is ok but I recommend you should always, before writing the file, open the map ori and mod it with software (ECM for example) and re-save the map mod to have a checksum is already correct!
Thanks for the advice
Let it be a time...get the map above to whom I have given the addresses over bit for the switch and look for them on your map. Put them in the values and the time is not needed
Perfect Errecinque, week next beginning, in the meantime, read the map ori, unfortunately I still can not download the file, surely you will ask more tips. Thank you
Anyway, thank you Errecinque, the next I'll try changing the email address you posted.
Perfect Errecinque, week next beginning, in the meantime, read the map ori, unfortunately I still can not download the file, surely you will ask more tips. Thank you
Read it, and put it that you say the right addresses.
Read it, and put it that you say the right addresses.
Perfect! thanks again
For the experience, and already tested on various cars you only have the electronic exclusion with the cleaning of the egr, nn serving closing physical because nn no problem, this insured and tested. (To be noted, however, that the Egr is working)
For the experience, and already tested on various cars you only have the electronic exclusion with the cleaning of the egr, nn serving closing physical because nn no problem, this insured and tested. (To be noted, however, that the Egr is working)
Hello Antonio, I don't have the total certainty that it functions electrically, after the fault is cleared from the diagnosis, to the second and third use the car, turn on the anomaly, returning to check the error message says "egr valve locked closed", the mechanics is perfectly clean, and by pressing the mechanism with your finger, it seems to me normal....it will have lost strength the electric motor!? As soon as I way I remove the text from the diagnosis.
when you have time, you should see if it actually if everything works, otherwise the light will turn on always notify you of the anomaly of the egr, and them or replace or otherwise close all given that the mechanism does not function, and delete the reporting of the error from the ecu
when you have time, you should see if it actually if everything works, otherwise the light will turn on always notify you of the anomaly of the egr, and them or replace or otherwise close all given that the mechanism does not function, and delete the reporting of the error from the ecu
I think at this point is better to close everything and delete the error from the ecu...you can always do from the ECM?
Hello errecinque, I have removed the fap and uploaded the modified map as suggested. Everything is ok....the machine goes that this is a pleasure.
Some time ago I closed the egr only mechanically with the plate, and I have walked many miles with the light on....since a few weeks the light turns this off....strange...I cracked the plate?
I don't think perchĕ on the 147 I have a sheet perforated by 6 mm and the light remains on. Do you have any idea?
If you have the management egr excluded in the map it is normal to be turned off the light.
The management of egr this is been active
The management of egr this is been active
If you're able to do the switch off you can safely disable the egr. There are plenty of examples on the forum for this ecu
I first I disabled the EGR from the map and walked around for 3 years without lamination, no lights are on and the car was fine. Then, on the occasion of the removal of the intake manifold to remove the swirl I did put a sheet of stainless steel from 2mm on the egr side of the pipe that comes from the exhaust manifold and that's fine,
I learned thanks to the forum then it is fair to share to those who do not know. 1DE432 display 8-bit take it from 1 to 2 . 1e46ee in 16-bit carry from 400 to val max 65535. And the dpf is as if there were
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.